Case Connector Push-Out Tool

For late model G.M. Transmissions, there will be no more broken harness connecters with this tool. Designed to fit the plastic connecter for easy removal.

4L80E Piston Installer

Designed for accurate installation of the Steel Rubber Molded Inner Seal on the 1997 and later, 4L80E Forward Clutch Drums.

A4LD Sprag Loading Tool

This tool is necessary for installation of the Plastic caged Overdrive Sprag Assembly on 1993 and later A4LD Transmissions.

C-3/A4LD Pump Alignment Tool

Designed to center up through the Bellhousing Bushing and Input Shaft. This tool is necessary for proper alignment of the Pump and Plate to the Bellhousing.

CD4E Pump Alignment Pin Kit

These Pins are necessary for the exact alignment of CD4E Pump Halves

E4OD Overdrive Loading Tool

This specially designed hand-held shaft is for quick and easy installation of the overdrive and coast clutch drum assembly as a single unit on the Ford E40D.

E40D Diaphram Spring Compressor

E40D Clutch Diaphram Spring Fixture allows for quick and easy assembly and disassembly of the overdrive cylinder from the transmission case. Also assisting in the assembly and disassembly of the overdrive cylinder diaphram spring.

A500/528/618 Overdrive Spring Compressing Tool

This unity will assist builders in disassembly adn reassembly of the A500/A518 overdrive assemblies by simply bolting to the extension housing and utilizing a threaded rod to compress the direct spring for easy snap ring removal.

A500/518 Splined Pilot Shaft

This Splined Pilot Shaft was designed for alignment of the internal components on the A500/A518 and A618 overdrive units. Assists assembly while compressing the overdrive direct spring.

A606 Transfer Shaft Seal Installer

Used to press the two back-to-back transfer shaft seals into the A606 transmission casing. At the same time setting the seals to the correct depth. Also includes seal protector.

A606 Outer Differential Adjuster

Required during disassembly and assembly of the A606 Differential Assembly.

Used with a 1/2" drive socket and both assist in setting the correct differential preload.

A606 Inner Differential Adjuster

Required during disassembly and assembly of the A606 Differential Assembly.

Used with a 1/2" drive socket and both assist in setting the correct differential preload.

Rebuild Bench

Heavy duty rebuilding bench offers a tough, solid surface for your day-to-day automotive needs. Features a sloping 12 gauge work top, raised front edge and a moulded drain trough in the rear to prevent oil spills. All benches feature heavy gauge steel construction, and your choice of 8 ft. or 10 ft. lengths. Both benches are 30 inches wide.

Transmission Case Support Tool

Work Bench mounted transmission case support tool allows the technician to bolt any case assembly to this fixture for unit servicing. It provides 360° of rotation with four different locking positions 90° apart from each other, and features all steel construction.

Swing Out Table

This fixture was designed especially for our work tables and is a handy swing-out table for setting transmission cases on for servicing.

Foot Press

For quick and easy removal of snaprings and spring retainers from automatic transmission cases and clutch drums.

Tall Jack Stand

Tall Jack stand with adjustable screw post for handy under-vehicle servicing when the vehicle is on the lift. Minimum height is 66 inches and when fully extended it measures 75 inches tall, with an approximate capacity of 2900 lbs.

Mesh Parts Baskets

All-purpose steel mesh parts baskets ideal for hot tanks and solvent tanks. Don't loose any small components when cleaning small parts.

Slide Hammer

Durable lightweight 16 oz. Constructed from heat-treated steel and 6001-T6 Aluminium, the Slide Hammer assists in removal of pumps from automatic transmission.

39 Piece Bushing Driver Set

39 piece Bushing Driver Set, covers all domestic and import automatic transmission bushings and seals. All drivers are manufactured from 4140 heat-treated material for durability. This kit consists of 38 drivers & handles, hooks, wall-mounted board and an application chart.

Extra Long Driver Handle

Extra long Driver Handle. At 28 inches long, this piece is a must for replacement of transmission case bushings.

Bushing Driver Expansion Kit - Ford AX4N

The Bushing Driver Expansion Kit expands your original 39 Piece kit to also support a Ford AX4N/ GM4T0E/Ford CD4E Transmission. All drivers are manufactured from 4140 heat-treated material for durability. Each kit includes enough hooks and a pegboard to assist you in keeping your shop organized

Ford AX4N - Part # T220-AX4N
9 Bushing Drivers
2 Handles

GM4T40E - Part # T220-4T40E
13 Bushing Drivers
2 Handles

Hot Flush - Transmission Cooler Line Flushing System

The Hot Flush transmission cooler line flushing system is designed to increase your shops efficiency and reduce warranty and come back problems

Better Engineering Mrg. Inc.'s Viper-Jets Washing System

Better Engineering's Viper-Jet series was specifically designed to fill the needs of both automotive and truck repair shops. From Cat dealers to car dealers, "B.E." jet washers are saving labor, boosting sales, and getting rid of solvents.

Pump Gear Alignment Tool Set

Transmission Re-builders Pump Gear Alignment Set

A604/606 Spring Compressor Tool

Chrysler A604/606 Low & Reverse Spring Compressor Tool

A must for all Transmission Re-Builders